manual for configuring a router of Zyxel Keenetic Lite 3

By | 10.12.2018



Instructions for configuring a router of Zyxel Keenetic Lite 3

Keenetic Lite 3 is one of the updated line of routers from Zyxel. All its products have received hardware upgrades and new firmware. That is why the setting of this router is somewhat different from his predecessors. Next, we will discuss in more detail each step of the process.

Kit & appearance

Owners of earlier models will immediately determine the number of external differences, which have received Keenetic Lite. It’s all the same black and compact the router, but the antenna are on the back and on the sides, making it easy to mount on the wall.

The bottom is made of glossy, matte side panels, and the top is the signature wave pattern. On the rear panel is now a hardware switch modes. The performance indicators are on the front of the router and in the active mode light up green. They flash so often, and so do not attract attention.

Инструкция по настройке роутера Zyxel Keenetic Lite 3

The set of router includes:

  • the device itself;
  • power supply;
  • network patch cord;
  • detailed instructions;
  • warranty card;
  • a brochure with other products of the company.

Connecting the router

Start the connection:

  1. unpack the router and its elements;
  2. connected to the power adapter and insert it into the socket;

    Инструкция по настройке роутера Zyxel Keenetic Lite 3

  3. connect the Internet cable from ISP to the WAN interface;
  4. using the patch cord connecting one of the LAN ports and plug the network card of your PC.

The router is ready for further work.

Entrance

Go to the basic setup of the router is Zyxel Keenetic Lite 3.

For starters, go to its interfacewith:

  • open the browser and in the address specify «192.168.1.1»;

    Инструкция по настройке роутера Zyxel Keenetic Lite 3

  • in the username field enter «admin», password is the standard «1234».

We have a menu of a router, necessary for further settings.

Инструкция по настройке роутера Zyxel Keenetic Lite 3

Configure Internet protocols

After entering the Configurator, you can use the «quick setup Wizard» that allows you to automatically obtain the simplest network settings. Next, we consider the process of connecting to the network for each of the types of connections.

L2TP

This type of Protocol used by the provider Beeline. To establish communication with such a network, we need to create 2 connections which use dynamic IP address and L2TP tunnel.

Create first:

  1. go to the «Internet» and then tab «Connection»;
  2. click on «Broadband connection»;
  3. check that the opposite WAN port, highlighted in blue were active checkbox;

    Инструкция по настройке роутера Zyxel Keenetic Lite 3

Attention! If you are planning to use IPTV, you also check boxes corresponding to the port in this menu.

  1. check the presence of ticks opposite to two points – the «Enable interface» and «Use for Internet access»;
  2. in the «IP settings» set «Automatically»;

Important! Previous item binding. If it leave «No IP address», even with all other correct settings, the connection will not work.

  1. click «Apply».

After this procedure, you can begin to create a L2TP connection:

  1. from the main menu, open the tab «PPPoE/VPN»;
  2. select «Add connection»;
  3. set a checkmark in «Enable» and «Use for Internet access»;
  4. in the field «Protocol Type» set to «L2TP»;

    Инструкция по настройке роутера Zyxel Keenetic Lite 3

  5. in the line «server Address» specify «tp.internet.beeline.ru;
  6. specify the user name and password provided by our ISP (usually found in the contract or specified in the technical support);
  7. in the «configure IP settings» set «Automatically»;
  8. click «Apply», save your changes.

Now you can connect your cable provider to your router (if you do not already have one) and check for access to the Internet.

PPPoE

If you use the services of the ISPs Rostelecom, Dom.ru and TTK, we need to configure the PPPoE connection.

Attention! Some of the branches of the above providers is PPPoE connection may use a different type – dynamic IP address. To verify this information from technical support.

Start the connection:

  1. go to the menu «Internet» and the tab «Connection»;
  2. find «Broadband connection» and click on it;
  3. put a check in the «Use socket»;
  4. check to active the option «Enable» and «Use for Internet access»;
  5. in the «IP settings» put the «No IP address»;
  6. in the column «MAC address» specify «default»;
  7. click «Apply».

    Инструкция по настройке роутера Zyxel Keenetic Lite 3

Next we need to create the type of connection authorization:

  1. go to the «PPPoE/VPN»;
  2. click «Add connection»;
  3. activate the checkmark at «Enable»;
  4. in the description field, specify a name for your connection (any Latin);
  5. the Protocol type, specify the «PPPoE»;
  6. in the «Connect via» specify the previously customized «Broadband…»;
  7. specify a name for the service or leave this field blank;
  8. specify the username and password for the connection;
  9. «Authentication method», select «Auto»;
  10. click «Apply»;
  11. connect the cable of the ISP to the WAN port and check the connection to the network.

Video: router ZyXEL Keenetic Lite III

DHCP

For this type of communication using the automatic receipt of IP, we will need to do the following:

  • open the tab «Internet» and choose «Connect»;
  • in the «configure IP settings» is set «Automatic»;
  • click «Apply».

Setup 3G Internet

To configure the 3G connection, follow these recommendations:

  1. go to «System», then «Components» and make sure that you enable «wireless modems for 3G networks «;
  2. if it is not active – it will have to install from the official site using the normal connection on the PC;
  3. go to the web interface, copying it into the address bar «192.168.1.1»;

    Инструкция по настройке роутера Zyxel Keenetic Lite 3

  4. enter the user name «admin» and password is «1234»;
  5. go to the advanced section and select «Configuration 3G»;
  6. put a check next to «Enable 3G backup»;
  7. specified operator settings, click «Save»;
  8. plug a 3G modem to the device using a USB extension cable and check the connection.

Please note! For each operator-specific settings 7 the item will be different. To clarify they can have technical support provider.

Wi-fi

To install the Wi-Fi connection:

  1. go to the router interface;
  2. select «Wi-Fi» and then the tab «access Point»;

    Инструкция по настройке роутера Zyxel Keenetic Lite 3

  3. specify a name for the connection (it can be any word written in the Latin alphabet);
  4. security mode – specify «WPA2-PSK»;
  5. in the «network Key» enter the password to connection;
  6. click «Apply».

Attention! After the connection, the router will automatically connect to the Internet without requiring every time to click on the label.

IPTV

Proceed with connecting the IPTV function:

  1. go to the router interface by typing in the browser address is «192.168.1.1»;
  2. enter the login name and password are «admin» and «1234»;
  3. in the bottom of the menu click on the network icon;
  4. select «Connection» and then click on «Broadband Connection»;

    Инструкция по настройке роутера Zyxel Keenetic Lite 3

  5. note a tick «to Use a connector…» and «Use for Internet access»;
  6. in the «IP settings» expose «Automatically»;

Important! This step can vary some providers. If the operator does not support automatic obtaining IP, then select «No IP address». This information is available from the service provider.

  1. note the «Enable» and «to Use a connector» opposite to the 4th port used to connect consoles;
  2. save the changes.

Update

Like any other program, for Keenetic Lite 3 requires timely updating. This can be done in the following way:

  1. launch any browser and go to the address «192.168.1.1 «;
  2. enter the login name and password (admin and 1234), click «OK»;
  3. in the main menu, pay attention to the version of the software and compare it with that shown at the bottom of the device;

    Инструкция по настройке роутера Zyxel Keenetic Lite 3

  4. if the router needs to be updated – downloaded it from the site, specifying the directory on your PC;
  5. unpack the resulting archive.
  6. again go to the menu, click «System» and then «Firmware»;
  7. click «Browse» and specify the path to the folder where you saved the file;
  8. find the one with the extension «bin» and select it;
  9. click «Update» and wait for the end of the process.

Attention! The update takes a few minutes. At this time, do not turn off the router to avoid further errors in his work.

When the router will reset and restart – re-enter login details and in the string version see installed update. After that it is recommended to change the default password and login. This can be done in the tab «System» and «Users» by clicking twice on the required data and modifying them.

Zyxel Keenetic Lite 3 – reliable and easy to handle router. Its setting is almost similar to previous versions. If you are faced with this procedure for the first time – just follow our simple instructions, or ask questions in the comments to the article.




Добавить комментарий

Ваш e-mail не будет опубликован. Обязательные поля помечены *